What did you do to your RHO Today?

[mghtymous21]

View attachment 29568View attachment 29569Last 2 mods done- running boards, hood decal.

Did you do the hood graphic yourself? Looks good

 

[MurderedCat]

View attachment 29568View attachment 29569Last 2 mods done- running boards, hood decal.

Where’d you get the decal?

 

[RHO89]

Pulled the camper to the Oregon coast today. Pulled great. Heres a view of the site. Cape Lookout State Park

 

[Ryand15]

Did you do the hood graphic yourself? Looks good

I did apply it myself. It laid really nice for me. Thanks!

 

[Ryand15]

Where’d you get the decal?

Anchor room

 

[MurderedCat]

Pulled the camper to the Oregon coast today. Pulled great. Heres a view of the site. Cape Lookout State Park
View attachment 29575
View attachment 29576
View attachment 29574View attachment 29573

MPG towing?

 

[RHO89]

MPG towing?

About 10 mpg, hwy and backroads.

 

[MurderedCat]

About 10 mpg, hwy and backroads.

Not bad!

 

[RHOJohnnie]

Got me some tint, and added the RB20's. Wish they said GoRhino instead of realtruck, but it is what it is. RC hard roll-up cover going on this weekend, along with Ark minis.

 

[Mac35]

Got all my badges (yes, we need stinkin' badges) on my RHO inside and out, and finally had time to make a post. I had some issues with the tailgate badge, but @BigRay took care of me with a free carbon fiber key fob and assistance. I got the Flame Red RAM front logo before RAM decided to put it on the new TRX Thanks again, Ray!

Next stop...CAT6!


View attachment 28350View attachment 28351View attachment 28352

How did you put the grille badge on does it screw on from the back like this one?

 

[Mac35]

Got all my badges (yes, we need stinkin' badges) on my RHO inside and out, and finally had time to make a post. I had some issues with the tailgate badge, but @BigRay took care of me with a free carbon fiber key fob and assistance. I got the Flame Red RAM front logo before RAM decided to put it on the new TRX Thanks again, Ray!

Next stop...CAT6!


View attachment 28350View attachment 28351View attachment 28352

How did you put the grille badge on does it screw on from the back like this one?

 

[Mac35]

Got all my badges (yes, we need stinkin' badges) on my RHO inside and out, and finally had time to make a post. I had some issues with the tailgate badge, but @BigRay took care of me with a free carbon fiber key fob and assistance. I got the Flame Red RAM front logo before RAM decided to put it on the new TRX Thanks again, Ray!

Next stop...CAT6!


View attachment 28350View attachment 28351View attachment 28352

How did you put the grille badge on does it screw on from the back like this one?

 

[RHOdy]

Pulled the camper to the Oregon coast today. Pulled great. Heres a view of the site. Cape Lookout State Park
View attachment 29575
View attachment 29576
View attachment 29574View attachment 29573

NOICE!

 

[Jprovance1]

Takes a lot of confidence to brag about it being small, good job

Hahaha

 

[Jprovance1]

I think I’m leaning that way. Did you go with the Airlift compressor setup?

 

[CORHinO]

How did you put the grille badge on does it screw on from the back like this one?

Good question. Assuming you're referring to the "RAM" lettering. No bolts needed, the OEM letters are affixed with 3M tape.

Here's the basic process:

1. Heat the OEM letters with a hair dryer or heat gun (if heat gun be careful with it, plastic will melt!)
2. Use fishing line to slowly/gently run it behind the OEM letters to remove them. Patience is a virtue here and is the most time consuming part of the process.
3. Clean off any leftover tape, then use a degreaser to prep.
4. Ray pre-applies 3M tape to the letters so you simply remove the backing, press the letters in place, hold for a few seconds, and that's it!

If memory serves, it took about an hour to complete the job. Again, patience will lead to the best results.

 

[RHOJohnnie]

Installed the Ark micros as well today. Not bad looking. Would recommend for anyone looking for splash guards. Super easy to install.

 

[INTIMD8R]

How did you put the grille badge on does it screw on from the back like this one?

So if you are referring to the Exotic Innovations grill badges, those get attached from the front.
So you have the bracket for behind the grill and the front consists of two pieces. The screws will go through from the front then you have the actual badge with 3M tape that adheres to that mounted piece. Very clean install.
Hope that explained it well enough.

 

[SOLAR]

Fresh Expel full ceramic coating done today !!

 

[FernNetty]

Added some more red. Reinstalled the JB4 and updated firmware. No issues so far running MAP2.